ruthart
Q: how big is the diameter on the hole
zapytał BG782340512 na 2021-04-30 11:34:44
ruthart The hole is 5mm diameter.
2021-04-30 12:52:47 Pomocny (0)Q: Does this board have a programmer on board?
zapytał trypesdg na 2021-03-28 08:22:52
ruthart It has a boot loader. If you write a program in the Arduino IDE or PlatformIO you can upload it through the USB port.
2021-03-28 09:12:48 Pomocny (0)Q: How bad is the backlash on these?
zapytał Bgsto na 2021-02-23 08:36:59
ruthart Backlash is undetectable. But keep in mind that there is a 64 times speed reduction gear inside so it is quite slow.
2021-02-24 07:05:03 Pomocny (1)Q: Will it work with tmc2208 stepper driver?
zapytał BG531791042 na 2021-02-16 12:49:09
ruthart Yes. Go to reprap.org and check out the wiki info for this board.
2021-02-16 01:50:29 Pomocny (0)Q: Is it suitable to be used for a DIY 3d printer?
zapytał R0203 na 2021-01-13 10:12:08
ruthart Yes, probably the best choice.
2021-01-13 11:21:26 Pomocny (0)Q: WHAT HOSE SIZE ARE THE INLET & OUTLET ???
zapytał BG171125920 na 2020-07-04 12:14:40
ruthart The thread is 0.5 inch pipe thread (od 20mm 14 threads per inch). the id is 12 - 13mm.The best fit is probably 0.5 inch hose.
2020-07-05 09:42:43 Pomocny (0)Q: What is the current draw of this magnet
zapytał BG161715491 na 2020-06-17 01:03:45
ruthart According to the specs 110mA.
2020-06-18 11:31:14 Pomocny (0)
ruthart Use a knife with a strong blade and pry it open at the corners. You have to apply some force but I was able to open it. The LED is next to the battery area.
2020-05-15 10:28:02 Pomocny (0)Q: What stepper motor will this work with?
zapytał ancsvc na 2020-05-06 01:21:20
ruthart Any nema 17 stepper will work. You don't need high torque.
2020-05-06 08:34:18 Pomocny (0)
Serdecznie zapraszamy do zasubskrybowania e-maila z zaproszeniem!
Jeśli się zapiszesz, zaprosimy Cię e-mailem, aby odpowiedzieć na pytania ludzi dotyczące produktów. Subskrybując Ciebie], zdobędziesz także "Pomocną odznakę "! Możesz zrezygnować z subskrypcji w dowolnym momencie na stronie ustawień prywatności.
Pomóż innym i bądź szczęśliwszy!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ruthart It generates a signal which can be used by your main board if so equipped. It would stop the print, record the position and sound the alarm. You may have to modify the firmware for this to work.
2021-09-24 07:06:50 Pomocny (0)