Wszystkie wiadomości

Bricola 10/06/2022
Receive quickly and in good condition, packaging OK. For assembly, you must also provide a multimeter for the resistors. Indeed, the marking (4 bands of color +1 for tol) is not always clearly visible. For the pitches, the marking on the board is sometimes not very clear. Refer to the photos on the site (ok I re-wrote on see image 2). The resistors are in the tolerance range of 5% error (while the brown band = 1%). The measurement of a 1000 ohm can be 970 ohms or 1001 ohms. A measurement repeating with a precision multimeter should confirm. All electrolytic capacitors are 100uF by 16Vdc, so no need to sort them. The pads for the connection of the elements are not simple to handel for soldering. Care must be taken that the pad does not "go" to the other side while soldering. It's quite a hassle to solder. Be careful not to overheat though. NOTE: JP1 bridge must be closed (open only if there is the option for the charger)! R29 is not installed, it is normal, at least for this version. Ok, the module is working correctly: Note: point V4 is at 5V and not at 1.5V ! Warning: if a key is stuck at startup (boot), the screen remains frozen when the version is displayed. Same with COM. If the COM port is open, this blocks the start of the unit. Otherwise, the COM works fine. Note that for the coils, the value of Z is at x.xx while it is displayed at x.xxxx. Further tests need to be done. For the case: It's really tricky to install. Be careful not to over-tighten the screws or risk cracking - breaking the case (upper or/and lower plate). Be careful not to jam a key. In overall, the product is fine and good. I think the battery connector has to use (take it in account with the to case) this will make the unit autonomous.
2
Zalecenia
Komentarze (2)

Q: Does it come with a 2 pins connector as well?

zapytał vchatzim na 2023-06-03 09:53:22

Bricola No. There is no connector, it's free lead (you may see this on pictures).

2023-06-03 03:57:46 Pomocny (1)
Zatwierdź
odpowiedzi (1)

Q: can I cut them to size?

zapytał BG738251313 na 2023-04-10 04:59:47

Bricola Yes you can. Using a saw or other cutting device that can cut this kind of material.

2023-04-11 03:13:39 Pomocny (0)
Zatwierdź
odpowiedzi (3)

Q: is this tips compatible with dremel 3000 ?

zapytał smoke0man na 2023-02-22 09:40:34

Bricola Normaly must fit with the Multi Chuck (0.8-3.2 mm) (Art 4486) from Dreimel (compatible with the 3000 serie), unless it's up to 3.2mm and the shank diameter of the tip is 3.175mm it must fit. I did not test it, but I think it's ok.

2023-02-23 06:33:06 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: Will the display work with Ubuntu Linux?

zapytał BG332163416 na 2022-09-22 11:26:43

Bricola Hello, I've put some info on the question : Is there a place to find more themes than the already installed? By the way, there is a possibility to use (run) the software on other OS, like Linux, MAcOS or other operating systems that support Python 3.x . It existing a "Turing Smart Screen Python” project hosted on Github. Take a look at cnx-software com

2022-09-23 07:24:05 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Bricola Shell only (without LCR module) is about 10$US, the LCR module itself (without the shell) is about 56$US. You can clearly see the difference while select.

2022-09-16 02:01:34 Pomocny (1)
Zatwierdź
odpowiedzi (1)

Bricola It's an adjustable DC Power Supply, not a simple jump starter or a welding unit. Not the same use, not the same pupose.

2022-09-05 08:46:23 Pomocny (0)
Zatwierdź
odpowiedzi (3)

Q: can I make my own theme?

zapytał BG425202414 na 2022-08-26 12:02:48

Bricola Hello, yes you can do your own theme. It's one of the feature that was a plus for me. You can have a look at the Question : "Is there a place to find more themes than the already installed?" and my answer. Hope this can help.

2022-08-27 11:09:28 Pomocny (1)
Zatwierdź
odpowiedzi (3)

Q: what is the current output of this device? thank you.

zapytał BG514437481 na 2022-08-09 04:21:39

Bricola Hello, I've just ordering one of this and waiting for it to arrive. Anyways, if you want to know the max current the output relay can support , regarding the specifications given : 20A by 12Vdc or 10A by 220VAC. No other output, no active output. Only a relay. It's a simple thermostat device.

2022-08-10 01:04:39 Pomocny (1)
Zatwierdź
odpowiedzi (2)

Q: What kind of 12V external power supply do you recommend ?

zapytał Bricola na 2022-08-08 03:10:52

The seller You can consult online customer service https://www.banggood.com/Contact-Us_hi111

2022-08-09 08:50:36 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: Is this a regulated output since there is a potentiometer

zapytał BG401755184 na 2021-12-07 02:26:00

Bricola AS jltt19 wrote on the 16.07.2020 , the output voltage is not fixed to 5V but can be between 2,7V to 10V depending of the pot setting from the factory. It is necessary to check and make the adjustment with the potentiometer for 5V. So, prior to supply the device that need the 5V, check the output of this module with a multimeter (voltage selected of course) and adjust the potentiometer. Then connect your device and check the 5V again, that might have drop a bit regarding the load, and if needed adjust carefully to 5V.

2022-08-03 01:39:25 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: There are 2 usb-c port in the back.. where to connect?

zapytał jvp4ant na 2022-05-26 03:17:33

Bricola Hello, I know, I've got the same question for myself, the installation paper was only half and cut ... After looking on the Internet, I found a video and some other infos. In fact, you have to connect the USB-C cable to the USB-C socket on the edge of the board, not the one in the middle (even thought there is not enough place for the connector). Install the software, connect the unit, install the driver (if needed), select a Theme and RUN. That's it.

2022-05-27 11:32:17 Pomocny (2)
Zatwierdź
odpowiedzi (2)

Bricola@MarcusStein Googlefor "3.5 Inch IPS TYPE-C Secondary Screen" or/and "How to get a cheap Sensor panel for your gaming PC mod" videos. It's only exemples, existing many others. Look at : drive_google_com \ drive \ folders \ 1H3L3C2pDzqeQ3fPw8nPMSdD9iJpZ1f4w change _ to . and \ to normal slash

Skaravaios 27/04/2022
8
Komentarze (3)

Q: Is there a place to find more themes than the already installed?

zapytał Skaravaios na 2022-04-27 05:26:44

Bricola I do not know, but you can create your own theme. There is a video you can watch on YTB : "_kRdJ65wO0o" that have a part which gives you tips how to do your own theme. Note that the size of images has to be 320x480 for portrait and 480x320 for landscape, has to be png. With the Theme Editor, you can load an existing theme (config directory) and change how you like. UI-Image is the back. By the way, there is a possibility to use (run) the software on other OS, like Linux, MAcOS or other operating systems that support Python 3.x . It existing a "Turing Smart Screen Python project hosted on Github. Take a look at cnx-software com : turing - smart - screen - a - low - cost - 3 - 5 - inch - usb - type - c - information - display , remove spaces before and after -.

2022-05-26 03:56:37 Pomocny (1)
Zatwierdź
odpowiedzi (1)