Wszystkie wiadomości

Q: can we use this as a SMD soldering?

zapytał gauravsanu na 2018-02-11 09:03:50

Kimiplayboy no it can't. it only reaches 150°C

2020-11-22 10:48:54 Pomocny (0)
odpowiedzi (2)

Tom no, you can set ON upon jesture, or press a button. battery can stand one day if you don't use it much, no SIM, no talks...

2020-09-16 01:30:31 Pomocny (0)
odpowiedzi (1)

Q: does it comes with case also?

zapytał gauravsanu na 2018-08-12 12:46:35

frisco_ita Nocase, components must be solded.

2020-06-28 08:47:08 Pomocny (0)
odpowiedzi (3)

Q: does this kit has original Tripath chip TA2020 020?

zapytał gauravsanu na 2019-04-14 08:04:32

tihotapac Yes

2020-02-17 02:31:08 Pomocny (0)
odpowiedzi (1)

Michal This one is Lepy LP-2020A.

2019-04-17 12:56:27 Pomocny (0)
odpowiedzi (1)

Q: Does it come with large capacitors and heat sink?

zapytał gauravsanu na 2019-02-27 12:50:57

Thurloug Guffaw it doesn't comes with large capacitors and heat sink

2019-03-05 05:07:20 Pomocny (0)
odpowiedzi (1)

Q: Can we use this speaker for Twitter only?

zapytał gauravsanu na 2019-02-24 03:33:13

emma Wow, that's cool. Maybe you can try.

2019-02-24 07:32:51 Pomocny (0)
odpowiedzi (1)

Q: Hello sir mujhe kuch item purches karna hai kasi karu

zapytał kewatsonu208 na 2018-09-07 10:25:32

gauravsanu Kaun sa item lena hai mujhe batao. Ya mujhe call karo 9971132145 me

2019-02-05 02:22:52 Pomocny (0)
odpowiedzi (4)

Q: can this amplifier be bridged to run mono?

zapytał jasperjay na 2018-10-22 08:26:08

gauravsanu does this amplifier is class D ?

2019-02-03 09:14:12 Pomocny (0)
odpowiedzi (2)

gauravsanu Nice and useful review.

Paul Kroon 2019-01-14 08:50:40
Not for the faint hearted. Yes, it requires soldering of SMD components. This item is more work than the smaller flat rotaters because you need to solder 4 24 pin SMD chips.It is definitely easier than the spheric rotator in which you must also solder the little LED's at the side of a PCB. It is not clear from the description that this model runs on 12V. But it is mentioned on the PCB and in the schematic. Testing can be done on 5V, because it will rotate, and the LED's will light up. But the turning is off. I have yet to find out how to set the clock. One person mentioned that the 1.5K resistors are missing. Yes, but a set of 2.2K resistors are provided instead. Use these. There are NO spare LED's, so be careful not to loose even one. I ordered the blue kit, which has a red LED on the most outwards position. But that LED is not supplied. I took one from my box with spares. Be careful with the LED receiver. Follow the manual as you have not to follow the direction on the PCB. This is mentioned on several places. For the DC female connector you must disobey the manual as it is wrong at that point. Ignore the middle connector. I blew the U4 chip, with the result that LED 5 will not light up. I might repair that later on. Otherwise: a decent kit, but certainly a bit expensive. Oh, and I have not been busy with the reprogramming. All is in Chinese. I have to subtract points for that one. Their appear to be only 3 pre-loaded pictures. Value for price: too expensive, costs 2 points. Quality: for the exchanged resistors, missing outer LED, lack of description on how to set the clock, costs 2 points Appearance: lack of english description on how to replace the code: costs 1 point.
Komentarze (5)

gauravsanu but it's very easily doable. you can send to me at,

2019-01-10 09:37:21 Pomocny (0)
odpowiedzi (2)