Najlepsze oferty na Drukarka 3D,DOPROWADZIŁO,Akumulator lipo

Dovcharov 08/12/2020

Amazing housing for my 3d printer. now my ABS prints are ok. Also reduces noise. you will need a cable extension kit for this housing to keep the control block outside. Also a number of tweaks are required, since your stepper motors may start to overheat. I tuned down the current on my Y and E axes to keep my motors cooler (vref tuned down to 0.6 vs original 0.75), and I plan to replace my printer mobo to SKR MINI E3 2.0 with quiet and cold TMC2209 stepper drivers

Creality 3D® Duży Osłon dla drukarki 3D Ender-5/5 pro/5 plus/CR-10Pro/10 V2 z folii aluminiowej o odporności na ogień

132,13€ 137,46€

2

Komentarze (0)

Dovcharov 09/06/2020

If you need to pass through the LED strip signal from the flight controller to the BEC board, solder the small "L" jumper near the DIN/S pad, and cut off the top of the mode selection button on the BEC board. "L" jumper connects the DIN\S pad to control wires of led strips, and broken mode button stops output of internal PWM generator of the BEC board. Obviously, after such change you will only be able to control the connected LED strips via the flight controller. "P" jumper works another way. When it is soldered, the PWM signal of internal led strip signal generator of the BEC board outputs through DIN/S pad as well. So you may control additional LED strips from one LED board.

LANTIANRC WS2812 Led Strip Light 20 Lamp 5V 0.23A Moduł Control Board dla RC FPV Racing Drone Night Flying

4,81€ 7,21€

4

Komentarze (0)

Dovcharov 23/06/2020

Good battery, but does not fit Mobula 7 HD battery tray. Too thick. My mistake, unfortunately.

Gaoneng GNB 11.4V 300mAh 80C 3S XT30 Wtyczka Bateria Lipo do dronów URUAV UR85 / UR85HD Mobula7 HD Sailfly-X RC

14,91€ 15,68€

0

Komentarze (0)

Dovcharov 09/06/2020

Great slim props for 6s racing drone.

2 pary Gemfan Hurricane 51466 5-calowy trwały 3-ostrzowy śmigło Wsparcie POPO dla RC Drone FPV Racing

7,45€ 8,29€

0

Komentarze (0)

Dovcharov Buyan iFlight mod for your DJI FPV goggles, and install Rapidfire module into them.

shrekowski 12/09/2019

Wow just would like to say Dogital FPV it is amazing , Is like to change CRT tv to LCD... From now HDO with rapidfire and crossfire will collect dust.

System DJI Digital FPV Air Unit 5.8GHz 8-kanałowy nadajnik HD 1080P Kamera 1440X810 Kombajn Okularów z Pilotem Tryb 2 Super niska opóźnienie do dronów wyścigowych RC

892,61€ 1.190,15€

8

Komentarze (2)

ZOHD Talon GT Rebel 1000mm Rozpiętość skrzydeł V-Tail BEPP FPV Samolot RC Samolot Latające skrzydło PNP

285,08€ 342,09€

Q: отзыв написать не могу пишу сюда,после 1 минуты работы на полном газу в моторе отклеялось половина магнитов,)что-то первый раз такое встречаю))))

zapytał Luxss na 2019-08-10 05:20:55

Dovcharov Да, штатный мотор - шлак. Бери на замену SunnySky X2216 2й или 3й версии 1250KV. У меня пока родной мотор от Талона работает, магниты на месте. Но мне видимо повезло.

2019-10-24 01:59:46 Pomocny

Zatwierdź

odpowiedzi (1)

Dovcharov 11/06/2018

This is a nice frame light and solid. Good looks. The front "canopy" fits Runcam Micro Eagle camera just fine. The only drawback I found is that frontal horizontal standoff comes with M3 thread however all the screws and holes in frame are M2. So front horizontal standoff needs to be replaced or holes in carbon fiber need to be drilled for M3 screws. Please note that stack mount holes are also M2 and motor mounts are for 11xx motors. You can use 20xx or 23xx props with this frame.