Wszystkie wiadomości

Q: When will Ender 3 Pro version be available?

zapytał NiPaH na 2023-01-17 04:55:41

SorinB It is already available. Read the full name of the item. All three mounting adaptors are included.

2023-01-18 02:37:10 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: Can I attach this on a black and decker drill?

zapytał dijolthomas na 2019-06-02 08:08:55

SorinB Thisis designed to be used with rotary tools compatible with Dremel, not with drills

2022-09-25 03:26:35 Pomocny (0)
Zatwierdź
odpowiedzi (4)

Q: can you use this on ender 5?

zapytał Boske na 2022-09-07 03:32:04

SorinB No as it is, because the attachments for the belts are different.

2022-09-08 02:28:40 Pomocny (0)
Zatwierdź
odpowiedzi (2)

SorinB I don't think so, because the mounting plate is different (the belt slots are in lower position for Ender 3). If you can manage that, anything else should work.

2022-05-10 02:33:52 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: Is this an official Creality upgrade kit?

zapytał Tom S na 2022-04-21 04:29:33

SorinB Yes, this is the real deal.

2022-04-22 09:17:32 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: what is the maximum temperature we can use on this

zapytał BG538161619 na 2022-02-21 04:20:49

SorinB The extruder is not fully metal, it has bowden tube inside, so the max temperature should not exceed 260 degrees centigrade.

2022-02-21 06:18:50 Pomocny (0)
Zatwierdź
odpowiedzi (4)

SorinB The voltage should be 24, not 1,4. Check where which end of the cable is going. The motor ends have two cables inverted and the one that connect with the original cable do not have that.

2022-02-09 03:17:24 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: How many steps?

zapytał DigitalAerialDesigns na 2022-01-26 11:31:49

SorinB For E-Steps, you can leave them unchanged, since the stepper motor is identical on both extruders. For precise calibration, there can be some small differences between the two stepper motors, so you can run the extruder calibration routine. About replacing, only two steps: 1- remove the old gear; 2- install the new one.

2022-01-27 09:27:38 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: does it fit on alfawise u30pro?

zapytał davcbr na 2020-09-13 03:28:04

SorinB Yes,it may fit if the belt fits. The V-slot wheels are at the same distance and the wires are long enough, no worry about that.

2022-01-17 05:16:17 Pomocny (0)
Zatwierdź
odpowiedzi (4)

Q: would this work for a cr10s pro?

zapytał Paulloth21 na 2020-03-27 07:26:21

SorinB Itworks wit any printer that accept auto bed leveling sensor (that have the dedicated pins on the mainboard or near the print head), with the appropriate firmware.

2022-01-17 05:05:19 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: can be used for tig welding?

zapytał joeclone na 2018-08-13 01:47:46

SorinB Youdon't need TIG, the rods are intended for use with a blowtorch. But, yes, i think you can.

2022-01-17 05:02:06 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: Is this compatible with Ender 3 Max?

zapytał BG364754465 na 2022-01-11 07:18:36

SorinB No, because the threaded rod is shorter. Everything else should be OK.

2022-01-11 08:53:14 Pomocny (0)
Zatwierdź
odpowiedzi (1)