Recenzje 22 w 1 Symulator lotu drona RC FPV z kzdolnym dla G7 Phoenix 5.0 XTR VRC FPV Racing Kompatybilny z nadajnikiem Radiolink/WFLY/FUTABA/FlySky/Walkera

22 w 1 Symulator lotu drona RC FPV z kzdolnym dla G7 Phoenix 5.0 XTR VRC FPV Racing Kompatybilny z nadajnikiem Radiolink/WFLY/FUTABA/FlySky/Walkera

US$14.99

Kup Teraz

Opinie klientów

4.9 z5

Zobacz wszystkie recenzje w3040

Napisać recenzję Uzyskaj podwójne oceny, jeśli jesteś jedną z pierwszych 3 opublikowanych recenzji!

Wszystkie recenzje(3040)
Obrazy
Wideo(3)
Wszystkie gwiazdy
- Wszystkie gwiazdy(3040)
- 5 Gwiazda(2836)
- 4 Gwiazda(148)
- 3 Gwiazda(28)
- 2 Gwiazda(11)
- 1 Gwiazda(17)

Sortuj według:

Do podglądu

Do podglądu
Najbardziej pomocny
Najnowszy

Recenzje tylko z Twojego kraju (Poland)

Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

Sky007FRVIP1
FR
04/02/2016

The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider
24

Komentarze (1)

Pokaż oryginał
three28isVIP1
US
06/01/2017

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.
20

Komentarze (1)

Pokaż oryginał