Wszystkie wiadomości

Q: Can I use LaserGRBL software?

zapytał grimmari na 2020-09-10 07:10:52

rewrew I strongly suspect that the hardware is quite-standard CNC, marlin and (Lasaer) GRBL compatible. From "Laser" GBRL: That might be geared towards "laser" applications where the laser can turn on and off on very short notice, while the spindle will take some time to spin up or -down. Or are you planning on adding a laser module?

2020-09-10 08:32:49 Pomocny (0)
Zatwierdź
odpowiedzi (5)

rewrew Hi Jeff. Banggood invited me as a customer to answer your question. Yes, I think it is a 5.5x2.5 standard connector. Yes, I think Banggood sells adapters too. https://www.banggood.com/AC-100V-240V-DC-24V-4A-96W-Power-Supply-Charger-Converter-Adapter-p-970663.html?rmmds=search or a bit more expensive: https://www.banggood.com/5_5mm-x-2_5mm-AC-100-240V-to-DC-24V-4A-Switching-Power-Supply-Adapter-Transformer-p-1092146.html?rmmds=search

2020-06-04 07:46:49 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: Is this a label printer? And is the label size 4 x 6 inch?

zapytał priyamlahon na 2019-10-14 04:01:24

rewrew This is a label printer. It prints 100mm or about 4 inches wide. You can buy various label sizes as long as they are not wider than that 4". So 4"x6" is certainly possible. But for example I've also seen labels offered that are 100x100 mm (4"x4", square). That should work too.

2020-05-16 10:32:25 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: can use thermal roller for receipt wide 57mm?

zapytał Serine na 2020-05-08 11:47:40

rewrew Yes, the print-width is about 100mm, but if you want to print 58 mm wide labels that's possible too. There are guides inside that you can put closer together to guide the 57mm labels to run in the middle of the machine.

2020-05-16 10:30:15 Pomocny (0)
Zatwierdź
odpowiedzi (1)

rewrew Theframerate is low when you put the sensor in the highest resolution. For real-time work you can better select a slightly lower resolution, allowing things to work in real-time. For "archive" pictures you then can select a higher resolution.

MarioP 2018-07-27 08:14:44
0
Komentarze (2)

Q: Is it possible to see the images in real time by the computer?

zapytał Gladson Araujo na 2018-10-30 07:17:21

rewrew Yes. When you set the resolution to 640x480, you get fast updates and can position, zoom, pan and focus in real-time. Then you can switch to 1280x720 and take a picture. (So far I have not been able to find the 1920x1080 mode that is claimed for the sensor resolution nor the 1280x960 that is mentioned somewhere).

2019-05-31 03:28:00 Pomocny (0)
Zatwierdź
odpowiedzi (2)

Q: Lifting table would be strong enough to make pcb repair on it?

zapytał Isabelbang na 2018-11-29 12:18:59

rewrew No, The table flexes a lot if you touch it. The rest of the microscope is quite sturdy but the table flexes a lot.

2019-05-30 12:33:52 Pomocny (0)
Zatwierdź
odpowiedzi (1)

rewrew Your question is valid. Current state-of-the-art goes a bit above 3000mAh nowadays, but in my experience, the 6000mAh for ten batteries TOTAL (600mAh / cell) is quite likely. Why make 3000mAh batteries, and claim 6000mAh? If you are going lie, you can just as well go all the way. The goal here is to have your acceptance of the goods ("the device powers up") before you find out that the capacity is really very small.

2018-05-19 06:20:58 Pomocny (2)
Zatwierdź
odpowiedzi (4)