Wszystkie wiadomości

george7n Yes, just bind it to your receiver and then it flies just fine....

2021-11-22 05:19:00 Pomocny (0)
Zatwierdź
odpowiedzi (0)

Q: Is this product have any warranty?

zapytał Duhara na 2021-11-13 02:16:43

george7n yes, 1-year warranty as usually.... please note that Blitzwolf products are of very good quality.... I have several of their products (like 5 of these cards 128GB ones) and never had an issue with them... that's why I always try to buy Blitzwolf...

2021-11-13 02:30:12 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: what size motors 1103? what size stack ?

zapytał BG184817422 na 2021-11-03 03:13:06

george7n For 1103 motors I would be using a 10A ESC (better 12 or 15A)... props 2 inch....battery 2S.... motor KV: 8k ~ 10k

2021-11-08 09:42:58 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: what size stack ? will it accept 1103 motors ?

zapytał BG184817422 na 2021-11-03 03:12:40

george7n yes, you can install 1103 motors on this one.... they support 4 motor holes

2021-11-08 09:38:51 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: Work with Kiss V2?

zapytał Trunks na 2021-11-05 04:00:36

george7n yes, sure it should work .. just add an ELRS receiver onto your KISS FC board

2021-11-08 09:28:34 Pomocny (0)
Zatwierdź
odpowiedzi (4)

Q: Flysky work with jumper tlite 4in1?

zapytał BG134203221 na 2021-10-28 11:52:33

george7n YES, the Jumper T-Lite 4in1 supports Flysky AFHDS and AFHDS-2A transmitters...... .it will bind to HappyModel Mobula6 Flysky version quadcopter

2021-10-29 02:32:09 Pomocny (1)
Zatwierdź
odpowiedzi (2)

george7n yes, the onboard FrSky SPI receiver supports S-FHSS ... needs Betaflight 4.0.5 or above

2021-10-21 07:27:24 Pomocny (1)
Zatwierdź
odpowiedzi (1)

Q: Can I use betafpv transmitter with this copter?

zapytał BG912385244 na 2021-10-19 03:25:19

george7n the BetaFpv LiteRadio 2 SE supports FrSky D8 and also D16 protocols....so Yes, the FrSky version of this drone should bind to this transmismitter

2021-10-21 07:23:40 Pomocny (0)
Zatwierdź
odpowiedzi (2)

george7n yes, a bit pale ... guess this product is on the cheap side ...tried some more expensive ones from a known brand name and they are much better

2021-10-21 07:20:00 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: compatible with mobula6?

zapytał miLhouseven na 2021-10-21 04:56:33

george7n I have tried a normal sized FC (25x25) and it was hanging out near the propellers....soi this frame is only compatible with 1 type of FC ... the one designed for this setup...nothing else so far

2021-10-21 07:17:44 Pomocny (0)
Zatwierdź
odpowiedzi (4)

george7n swapped motors and now that motor spins kind of erratically?...yes, looks like the ESC on the board...you can try this process to fix but youigut have to replace that board entirely: 1_check for any physical contact issues (using a connection tester) on that motor connector on the board - I remember one time I had a similar issue and I simply re-soldeted that connector and that fixed the issue :-) also try 2_reflash your board in Betaflight and also reflash your ESC firmware in BLHeli....if still faulty then replace the FC board completely

george7n 24/03/2021
0
Komentarze (3)

george7n these have standardized mounting hole distances (just checked) for the 3-hole mounting design....around ~ 5.5mm....I have used them on many 3-holed frames and it was OK 👌

2021-10-06 02:30:48 Pomocny (0)
Zatwierdź
odpowiedzi (1)

george7n the Gemfan D51 has 5 blades and these ones have 4 blades. they both have a mounting hole of 1.5mm and 2" (~50mm) sized...YES, they both can be used on that Cine 8....Differences between blades used: with the 4 blade propeller you will get more speed compared to a 5 blade....however using the 5 blade will give you more stability-control compared to a 4 blade...my recommendatio is to use 5 blade if you after more stability in your footages....but if you want to film fast moving targets, then switch to 4 or even 3 blades

2021-10-06 02:07:32 Pomocny (0)
Zatwierdź
odpowiedzi (1)

Q: Are ipex 1?

zapytał mach74 na 2021-10-05 05:40:51

george7n these are the latest U.FL types => high frequency miniature coaxial interconnection type IPEX

2021-10-06 01:57:14 Pomocny (0)
Zatwierdź
odpowiedzi (1)

george7n well, I have managed to strip and cut some very small and thin wires....with a lot of patience :-)

2021-10-04 05:25:31 Pomocny (0)
Zatwierdź
odpowiedzi (3)