Jasonasselin
moje treści
Wszystkie wiadomości
Opinie
Komentarze
odpowiedzi
pytania

Wszystkie wiadomości

Jasonasselin 04/07/2020
boy was i happy this thing worked. i live in canada and have 220v split phase to my garage. hooked the vfd up and it powers up the little horizontal mill no problem. output was 400v at 60Hz, which is great. speed control works really good. my mill has a 2 speed motor, so i have to stop the vfd before i switch to the second speed or reverse with the mill control switch. VFD forward and reverse work and so does the deceleration time, which is pretty nice feature. the front panel is very cheap, but works. i ordered some nice push buttons and a potentiometer to make a wired control panel. motor i have is 380v three phase of unknown config (delta or wye) but worked with this unit. its supposed to run at 0.7Kw (2.4A) at 695rpm, and 1.1kw (2.4A) at 1400rpm, but it drew 3.5 and 4.0 amps respectively at 50hz each. i think this is fine. motor was very torquey at all speeds, i was not able to stall it with a 2x6 levering on the spindle sheave. the max amps it drew while i was trying to stall it was 4.2A. i am glad i over rated the drive for the motor demand, as it seems to be a bit hungry when not on real 3ph and it could have gone over a smaller spec one. the only thing i would have wanted is for it to use a standard type of plug for the control panel, so i could just remote mount the control for now, before i make the new panel. as i really want to install the drive way below in the casting as it makes a quiet but really annoying noise. sounds almost like bad bearing noise. had to pay duty or clearance whatever, of 40$ i think? i cant recall the exact amount. just expect that. would have been 5 stars if the case was better, the wire terminations were big enough for crimped wire ends, and if the panel used rj45 for an extension cable instead of random ribbon type. Either way, this will take my canadian spaghetti power and turn in into weird european 380v3ph and run a pretty decently powered mill. i am happy as long as it lasts a year or two for this price!
Przetwornik częstotliwości zmienna napięcia 2,2 KW 12A 220V 1 faza wejście, 3 fazy wyjście 380V z kontrolą wektora V/F
US$195.18 US$202.99
3
Zalecenia
Komentarze (3)

Jasonasselin still woks great. I only use it maybe once a month. But no issues so far.

Jasonasselin 04/07/2020
boy was i happy this thing worked. i live in canada and have 220v split phase to my garage. hooked the vfd up and it powers up the little horizontal mill no problem. output was 400v at 60Hz, which is great. speed control works really good. my mill has a 2 speed motor, so i have to stop the vfd before i switch to the second speed or reverse with the mill control switch. VFD forward and reverse work and so does the deceleration time, which is pretty nice feature. the front panel is very cheap, but works. i ordered some nice push buttons and a potentiometer to make a wired control panel. motor i have is 380v three phase of unknown config (delta or wye) but worked with this unit. its supposed to run at 0.7Kw (2.4A) at 695rpm, and 1.1kw (2.4A) at 1400rpm, but it drew 3.5 and 4.0 amps respectively at 50hz each. i think this is fine. motor was very torquey at all speeds, i was not able to stall it with a 2x6 levering on the spindle sheave. the max amps it drew while i was trying to stall it was 4.2A. i am glad i over rated the drive for the motor demand, as it seems to be a bit hungry when not on real 3ph and it could have gone over a smaller spec one. the only thing i would have wanted is for it to use a standard type of plug for the control panel, so i could just remote mount the control for now, before i make the new panel. as i really want to install the drive way below in the casting as it makes a quiet but really annoying noise. sounds almost like bad bearing noise. had to pay duty or clearance whatever, of 40$ i think? i cant recall the exact amount. just expect that. would have been 5 stars if the case was better, the wire terminations were big enough for crimped wire ends, and if the panel used rj45 for an extension cable instead of random ribbon type. Either way, this will take my canadian spaghetti power and turn in into weird european 380v3ph and run a pretty decently powered mill. i am happy as long as it lasts a year or two for this price!
Przetwornik częstotliwości zmienna napięcia 2,2 KW 12A 220V 1 faza wejście, 3 fazy wyjście 380V z kontrolą wektora V/F
US$195.18 US$202.99
3
Komentarze (3)
Przetwornik częstotliwości zmienna napięcia 2,2 KW 12A 220V 1 faza wejście, 3 fazy wyjście 380V z kontrolą wektora V/F
US$195.18 US$202.99

Q: How many Battery we use for this and please let me know what kind of Battery I use for this

zapytał BG552553210 na 2020-08-25 03:30:17

Jasonasselin There are no batteries for this unit

2020-11-30 04:28:55 Pomocny (0)
Zatwierdź
odpowiedzi (1)
Drillpro 10 szt. Wkładki z węgliku RCGT10T3 MOAK H01 Narzędzie do skrawania CNC Wykorzystywane do aluminium
US$21.93 US$22.99

Q: Will these work for a wood lathe tool? Is the top cupped (concave)?

zapytał BG971124111 na 2020-11-02 10:51:26

Jasonasselin Not sure if you want positive rake on a wood lathe, but yes, they are shaped like a tiny bowl, where the rim is raised above the middle.

2020-11-30 04:28:29 Pomocny (0)
Zatwierdź
odpowiedzi (1)
60 sztuk wodoodpornych złącz JST przewód pasków świetlnych LED 2-pinowy kabel złączowy lampa
US$11.54 US$11.99

Q: I get female and male when buy or just one of above?

zapytał andr188r na 2020-11-30 03:20:50

Jasonasselin Half female and half male is included in each “order”

2020-11-30 04:27:27 Pomocny (0)
Zatwierdź
odpowiedzi (3)
19 sztuk ER32 2-20mm zestaw zacisków sprężynowych z tulejką zaciskową do narzędzia tokarskiego CNC
US$75.99 US$91.99

Q: Can any one tell me if these collets are compatible with items ID 1073861 and ID 1285389 Thanks in advance

zapytał d5veh2 na 2020-10-04 03:38:45

Jasonasselin Yes. It works with 1073861. And all other ER32 holders.

2020-10-04 05:44:08 Pomocny (0)
Zatwierdź
odpowiedzi (1)
7 szt. Radełkowanie Narzędzie radełkowane Przekątne koło Zestaw radełek liniowych o skoku 0,5-2 mm
US$22.99 US$32.99

Q: How thick is the holder?

zapytał EgorXaker na 2018-05-19 05:39:23

Jasonasselin about20mm i had to grind mine down to fit in a BXA holder.

2020-08-07 02:40:10 Pomocny (1)
Zatwierdź
odpowiedzi (2)
19 sztuk ER32 2-20mm zestaw zacisków sprężynowych z tulejką zaciskową do narzędzia tokarskiego CNC
US$75.99 US$91.99

Q: What are the sizes in 19 collet set? Is it inch or mm?

zapytał PEAKEY na 2018-07-11 04:23:38

Jasonasselin theyare measured in MM, as an example one collet will say 3-4mm and will measure exactly 4mm inside.

2020-08-07 02:39:31 Pomocny (0)
Zatwierdź
odpowiedzi (2)
Przetwornik częstotliwości zmienna napięcia 2,2 KW 12A 220V 1 faza wejście, 3 fazy wyjście 380V z kontrolą wektora V/F
US$195.18 US$202.99

Q: i have a washing machine 220v./60 Hz. and can't work at 220v./50 Hz..could this product helps to change freq. from 50 to 60 Hz. with the same voltage ?.thank you

zapytał Eng.Osama Abu-Zid na 2019-03-02 03:20:47

Jasonasselin nothis drive outputs 380-400v, you can use a different drive to change the frequency. but it is likely your washer will work fine at 50 hz anyway. usually a washing machine is not 3 phase also, so better check that first

2020-08-07 02:38:34 Pomocny (0)
Zatwierdź
odpowiedzi (1)
Jasonasselin 03/07/2020
Packaging did not survive completely, but the plastic case the chuck came in held up and protected the unit very well. the threads are finished really smooth and the nut free spins 3/4 turn when spun. the grinding inside and finishing look really good, better than i was expecting. i Haven’t checked concentricity yet, but by the look of the fit and finish it should not disappoint. the only bummer is that i paid for shipping from three warehouses for this order, and as i am reviewing this item, i would sure like to have the collets to try it with lol. i was actually impressed enough to write a review. the quality so far is on par with the stuff i got from SHARS.
UCHWYT NA UCHWYT DO TOKARKI CNC MACHIFIT MT3-ER32 Z UCHWYTEM DO SKOKU MORSE'A
US$35.79 US$37.99
0
Zalecenia
Komentarze (0)
Jasonasselin 03/07/2020
units as received resemble the ones pictured. they feel nice and are straight. packaging was good. they were not dirty or covered in grinding dust. inserts have nice shape.
5 sztuk SCLCR 6/7/8/10/12mm tokarka wytaczadło stroik z 5 sztuk CCMT0602 wkładka
US$39.26 US$40.99
0
Zalecenia
Komentarze (0)

Jesteś ekspertem, czy możesz pomóc?

Serdecznie zapraszamy do zasubskrybowania e-maila z zaproszeniem!

Jeśli się zapiszesz, zaprosimy Cię e-mailem, aby odpowiedzieć na pytania ludzi dotyczące produktów. Subskrybując Ciebie], zdobędziesz także "Pomocną odznakę "! Możesz zrezygnować z subskrypcji w dowolnym momencie na stronie ustawień prywatności.

Pomóż innym i bądź szczęśliwszy!

  • Subskrybuj

O odznakach

Odznaki są powiązane ze społecznością, a użytkownicy zdobywają odznaki, tworząc wysokiej jakości treści, wykonując misje lub uczestnicząc w specjalnych działaniach. Określeni ludzie również będą mieli własną wyłączną odznakę.
Odznaka CEO

Odznaka CEO jest własnością tylko szefa Banggood.

Wkrótce otrzymasz odznaki, które możesz zdobyć
  • ok

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • ok

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe