+ Working as intended. + Good quality + Very useful + Smart chip offering a lot of functions + High gain - Nothing.

+ Working as intended. + Good quality + Very useful + Smart chip offering a lot of functions + High gain - Nothing.

+ Working as intended. + Good quality + Very useful + Smart chip offering a lot of functions + High gain - Nothing.

Excellent low noise microphone amplifier + electret microphone on it. Power it either with 3.3V or 5V, you may feed directly out to your Arduino ADC input. The output from this preamplifier is about half of the VCC voltage. There is AGC (Automatic Gain Control), but it may be bad if you want use it as YouTube microphone for your computer - while not talking, all background noises are amplified. To disable AGC, short together pins 13 and 14 on the chip, or better to adjacent resistors with designations "222" and "154". This way audio is more silent when not talking close to the microphone. I found also useful pre-amplifier for other things where no need bias resistor, just "raw" analog input. In this case use soldering iron and remove 2.2 kOhm resistor (designation "222"). This way bias voltage will be not present on input pin (just unsolder microphone capsule) and you have really great pre-amplifier for your projects (radio communications, various detectors, and so on). I will provide picture with place where to make short if you want to disable AGC. Next to this spot is resistor "222" which can be also removed together with microphone for use to other purposes as a high quality and low noise pre-amplifier. Bandwidth of this preamp is about 35 kHz.

Excellent low noise microphone amplifier + electret microphone on it. Power it either with 3.3V or 5V, you may feed directly out to your Arduino ADC input. The output from this preamplifier is about half of the VCC voltage. There is AGC (Automatic Gain Control), but it may be bad if you want use it as YouTube microphone for your computer - while not talking, all background noises are amplified. To disable AGC, short together pins 13 and 14 on the chip, or better to adjacent resistors with designations "222" and "154". This way audio is more silent when not talking close to the microphone. I found also useful pre-amplifier for other things where no need bias resistor, just "raw" analog input. In this case use soldering iron and remove 2.2 kOhm resistor (designation "222"). This way bias voltage will be not present on input pin (just unsolder microphone capsule) and you have really great pre-amplifier for your projects (radio communications, various detectors, and so on). I will provide picture with place where to make short if you want to disable AGC. Next to this spot is resistor "222" which can be also removed together with microphone for use to other purposes as a high quality and low noise pre-amplifier. Bandwidth of this preamp is about 35 kHz.

Excellent low noise microphone amplifier + electret microphone on it. Power it either with 3.3V or 5V, you may feed directly out to your Arduino ADC input. The output from this preamplifier is about half of the VCC voltage. There is AGC (Automatic Gain Control), but it may be bad if you want use it as YouTube microphone for your computer - while not talking, all background noises are amplified. To disable AGC, short together pins 13 and 14 on the chip, or better to adjacent resistors with designations "222" and "154". This way audio is more silent when not talking close to the microphone. I found also useful pre-amplifier for other things where no need bias resistor, just "raw" analog input. In this case use soldering iron and remove 2.2 kOhm resistor (designation "222"). This way bias voltage will be not present on input pin (just unsolder microphone capsule) and you have really great pre-amplifier for your projects (radio communications, various detectors, and so on). I will provide picture with place where to make short if you want to disable AGC. Next to this spot is resistor "222" which can be also removed together with microphone for use to other purposes as a high quality and low noise pre-amplifier. Bandwidth of this preamp is about 35 kHz.

Praca jako intencja, wysokie zyski.

Working as intendet. High gain.

Praca jako intencja, wysokie zyski.

Wszystko w porządku zgodnie z opisem.

Tudo ok, de acordo com a descrição.

Wszystko w porządku zgodnie z opisem.

Product arrived in good perfect condition

Product arrived in good perfect condition

Product arrived in good perfect condition

Item very good for various audio projects. I used it in a doorbell and it works fine.

Item very good for various audio projects. I used it in a doorbell and it works fine.

Item very good for various audio projects. I used it in a doorbell and it works fine.

Применение этих микрофонов с ардуино https://youtu.be/mk5nf10OP-E

Применение этих микрофонов с ардуино https://youtu.be/mk5nf10OP-E

Применение этих микрофонов с ардуино https://youtu.be/mk5nf10OP-E

Musiałem przymocować grunt do powłoki mikrofonu, żeby wyeliminować jakiś przerywany szum. Będąc aluminium, nie mogłem się do niego przylutować. Znalazłem dużą sprężynę o średnicy nieco mniejszej od mikrofonu, wyciąłem z niej jedną pętlę, przylutowałem do niej przewód, a potem przesunął przez mikrofon. Przywiązałem drut do podłoża i wtedy szum/brzęk zniknął.

Very good! Had to attach a ground to the shell of the microphone to eliminate some intermittent hum/buzz. Being aluminium, I could not solder to it. I found a large spring of a diameter a bit smaller than the mic, cut a single loop out of it, soldered a wire to it then slipped it over the microphone. I attached the wire to ground and then the hum/buzz disappeared.

Musiałem przymocować grunt do powłoki mikrofonu, żeby wyeliminować jakiś przerywany szum. Będąc aluminium, nie mogłem się do niego przylutować. Znalazłem dużą sprężynę o średnicy nieco mniejszej od mikrofonu, wyciąłem z niej jedną pętlę, przylutowałem do niej przewód, a potem przesunął przez mikrofon. Przywiązałem drut do podłoża i wtedy szum/brzęk zniknął.

ok!

ok!

ok!

Bardzo dobrze

Very good

Bardzo dobrze