Opinie klientów

Napisać recenzję
  • Wszystkie recenzje(91)
  • Obrazy
  • Wideo(0)
  • Wszystkie gwiazdy
    • Wszystkie gwiazdy(91)
    • 5 Gwiazda(78)
    • 4 Gwiazda(11)
    • 3 Gwiazda(2)
    • 2 Gwiazda(0)
    • 1 Gwiazda(0)
Sortuj według:
Do podglądu
  • Do podglądu
  • Najbardziej pomocny
  • Najnowszy
Recenzje tylko z Twojego kraju (Poland)
|
Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

  • 09/05/2020

    Dobra maszyna, potrzebuje trochę uaktualnień, żeby być perfekcyjną. Polecam ją wszystkim!

    Komentarze (1)
    Pokaż oryginał
  • 22/11/2019

    Fast delivery (6 days) from UK. Assembled in less than one hour. Printer works as expected, it was delivered without the glass plate and the aluminium print bed is not 100% flat, the middle is 0.1mm lower than the front and rear edge. (So only 4 stars for quality.) So far 4 out of 22 prints (20 are my own design) failed because of the print releasing from the bed during printing. I feel that is an acceptable result for someone new to 3D printing. I ordered the glass plate for the print bed and hope that will solve the prints releasing during printing.

    Komentarze
    Pokaż oryginał
  • 01/06/2021

    The printer has been delivered well before the expected date, i.e. nearly a week in advance. Very good ! The packaging is professional, the molded foam makes sure that all parts remain in place and are not damaged. The packaging list checks with the contents, a few goodies are also present: a mouse pad, and a tool to remove the print from the heated bed when it is finished. The only remark I have on the packaging is that the the two extruders are in a foam pocket with the screws left loose in the same pocket. No missing part, fortunately :) Assembling the printer is a matter of a couple of hours. Some challenge to fix the Z axis as one has to insert the screws from below without a good view. My first screw escaped into the body of the printer and I was nearly panicking not to be able to get it back, but I was OK with it at the end. The test print at the end with a colour gradient is very convincing. I could even check the 'end of filament' sensor as the small amount of filament in the box is not enough to complete the test print. As far as I can judge after a few hours print, I heartily recommend this printer. The quality of the test print is high and the colour mix is beautiful. The machine is a bit noisy when idle (the cooling fan of the power supply is quite noisy), but the moves during printing do not produce too much noise. I like the control panel for local printing from the SD card; I still need to do the tests from a PC or a raspberry with Octopi. Definitely satisfied with my purchase!

    Komentarze
    Pokaż oryginał
  • 12/05/2021

    j'ai bien reçu le colis, le carton est casser un.peu partout mais à l'ouverture je crois qu'il n'y a rien de casser, je verrai sa demain quand je le monterai. Merci PS: sous réserve

    Komentarze
    Pokaż oryginał
  • 28/08/2020

    Świetny produkt. Łatwy w montażu i użyciu. Konieczne było dostrojenie ustawień, aby uzyskać lepsze odciski. Szybka dostawa! Jeden wspornik silnikowy był wygięty prawdopodobnie podczas transportu, ale łatwo można go było wygiąć do tyłu.

    Komentarze (1)
    Pokaż oryginał
  • 10/06/2021

    Jestem zadowolony z produktu, otrzymałem go w mniej niż tydzień, dobrze zapakowany. Montaż jest bardzo prosty, zajęło mi 15-20 minut, aby go ustawić i uruchomić. Po aktualizacji tacki, zrobiłem mój pierwszy dwukolorowy żółty i biały druk (plik testowy podany na karcie SD) jest wspaniały. Bardzo dobra drukarka z dobrym rozmiarem tacki i nadruk, który jest możliwy w dwóch kolorach za nie przesadną cenę: Polecam.

    Komentarze
    Pokaż oryginał
  • 05/02/2021

    Colis dobrze emballé

    Komentarze
    Pokaż oryginał
  • 29/10/2019

    Дошёл из Китая в Харьков за 25 дней. Всё вроде цело, комплектация в порядке. Пока нет возможности собрать. Запущу - допишу отзыв!

    Komentarze
    Pokaż oryginał
  • 01/07/2019

    Tengo muchos problemas de adherencia con la primera capa, no trajo el superplate y lo que trae para poner encima de la cama caliente es muy malo

    Komentarze
    Pokaż oryginał
  • 14/01/2022

    Super drukarka 3d (drukarka 3d)

    Komentarze
    Pokaż oryginał
Show:

    Całkowity 0 stron

    Idź do strony

    Możesz być zainteresowany

    recommendation for you
    • US$584.00
    • US$839.00
    • US$199.00
    • US$479.00
    • US$369.00
    • US$249.00
    • US$462.00
    • US$169.00
    • US$329.00
    • US$649.00
    • US$299.00
    • US$449.00
    • US$194.00
    • US$322.00
    • US$282.00
    • US$219.00
    • US$399.00
    • US$979.00