Opinie klientów

Napisać recenzję
  • Wszystkie recenzje(658)
  • Obrazy
  • Wideo(3)
  • Wszystkie gwiazdy
    • Wszystkie gwiazdy(658)
    • 5 Gwiazda(615)
    • 4 Gwiazda(32)
    • 3 Gwiazda(7)
    • 2 Gwiazda(3)
    • 1 Gwiazda(1)
Sortuj według:
Do podglądu
  • Do podglądu
  • Najbardziej pomocny
  • Najnowszy
Recenzje tylko z Twojego kraju (Poland)
|
Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

  • 29/09/2015

    I took a chance on this, because I didn't think there was enough information in the description. I ordered the C version, with the 8x20mm motor, but unfortunately what arrived today was the A version, with 7x16mm motor, so the figures below are for the A version. I haven't powered it up yet, but I think it will be very suitable for an indoor slow flyer of the Vapor, Ember, Cub etc. style. With the 8x20mm motor probably something a bit bigger and/or faster. The prop has a diameter of 138mm, but no pitch marked. By comparing it with other props of known pitch I am guessing it is a 138x63 mm or 5425 inches. It came badly out of balance, but by taking tiny shavings off the heavy blade with a modelling knife, I eventually got it to balance perfectly. It is very light at 1.24g, and I don't think it would withstand a hard impact, but ideal for a slow flyer. The description says it has a .8mm hole, but when I measured the prop shaft, it is 1mm diameter. I tried pushing it into the prop and it is a very tight fit, but does go in. The gearbox is the usual two brass bush type, with plastic 9 tooth pinion and gear. I didn't count the teeth on the gear, but I'm guessing there are 54 giving a 6:1 ratio. The prop shaft is 27mm long with one end knurled for a length of about 8mm. I think the knurled end goes into the plastic nut provided, with the smooth end going into the prop, so you can remove and replace a prop without much trouble. Weight of the gearbox is 1.29g and of the motor 2.61g. Motor shaft is 1mm diameter. There is a square hole in the gearbox that I think is intended for mounting on the end of a square section carbon fibre rod, such as you might use for the fuselage of a very light slow flyer of the Vapor type. It looks as though it is a 2x2mm hole. It would probably be possible to mount the motor/gearbox other ways, e.g. with tiny cable ties or with glue. The proof will be in how it runs, but at this stage I think it's a very light and economical power plant for an indoor flyer, with flexibility in the choice of motor according to your intended use.

    Komentarze (5)
    Pokaż oryginał
  • 07/08/2019

    Great micro motor for ultra light aircraft under 4 ounces. It ships unassembled but assembly is easy. The propeller balance should be checked and corrected before use. The gear is a little noisy at low rpm but it smooths out at flying speed. I used one in a Guillow's Lancer airplane I converted from rubber power to electric motor and 3 channel RC. This motor and propeller provide more than enough thrust for this under 50 gram airplane.

    Komentarze (2)
    Pokaż oryginał
  • 26/09/2018

    Nice Motor....... Enough Thrust power to my DIY plane.....

    Komentarze (1)
    Pokaż oryginał
  • 12/12/2020

    Drobny i lekki zestaw do jazdy wolnolotem. Brak instrukcji o dupach, więc powinieneś spojrzeć na zdjęcie przed złożeniem. Krzewy muszą być dobrze ustawione, w przeciwnym razie szyb ma tendencję do zaciskania się i jazdy z dużym tarciem. Mój zestaw rysuje 80mA przy 4.0V (przy 1s lipo) i wykazuje pewne wibracje - zbalansuje rekwizyt i zobaczy, czy pociągnie wystarczająco na moją wewnętrzną ulotkę...

    Komentarze
    Pokaż oryginał
  • gozVIP3
    CA
    03/12/2020

    Ładny mały silnik trzeba jednak dostosować przepustnicę, aby mieć impuls startowy inaczej silnik nie będzie działał, włożę go na mini bukowiec z Banggood

    Komentarze (1)
    Pokaż oryginał
  • 14/10/2020

    Szybka dostawa, stan idealny, nie mogę się doczekać budowy

    Komentarze
    Pokaż oryginał
  • 08/11/2017

    this item is very good has super power i use for mini cessna airplain fly very good https://www.youtube.com/watch?v=sOhNC9UEu_U&feature=youtu.be

    Komentarze (1)
    Pokaż oryginał
  • 27/03/2020

    Generuje dobry ciąg przy niskim prądzie. Ale rekwizyt był całkowicie wyłączony z równowagi i generował silne wibracje. Musisz to zbalansować. Planowałem użyć go na moim 35cm szybowcu, ale jest za duży i ciężki. Lepszym wyborem jest silnik Racerstar 8520 z rekwizytem KingKong 65 mm - nawet jeśli prąd jest znacznie wyższy dla niższego ciągu.

    Komentarze
    Pokaż oryginał
  • 24/11/2018

    nice product but motor shaft is very tigh t and motor casing is very tight too you have to make that bigger to fit

    Komentarze
    Pokaż oryginał
  • 31/08/2017

    Works perfectly fine for small indoor models.

    Komentarze
    Pokaż oryginał
Show:

    Całkowity 0 stron

    Idź do strony

    Możesz być zainteresowany

    recommendation for you
    • US$18.99
    • US$8.99
    • US$17.31
    • US$5.50
    • US$10.99
    • US$25.29
    • US$5.99
    • US$9.99
    • US$5.59
    • US$69.99
    • US$12.99
    • US$35.99
    • US$5.50
    • US$33.94
    • US$12.99
    • US$42.99
    • US$14.99
    • US$6.99