Opinie klientów

Napisać recenzję
  • Wszystkie recenzje(32)
  • Obrazy
  • Wideo(1)
  • Wszystkie gwiazdy
    • Wszystkie gwiazdy(32)
    • 5 Gwiazda(30)
    • 4 Gwiazda(2)
    • 3 Gwiazda(0)
    • 2 Gwiazda(0)
    • 1 Gwiazda(0)
Sortuj według:
Do podglądu
  • Do podglądu
  • Najbardziej pomocny
  • Najnowszy
Recenzje tylko z Twojego kraju (Poland)
|
Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

  • 07/06/2016

    Basically a breakout board for the processor. Includes USB connection (2x 22Ohm resistors in series with D+ and D- and a D+ pull up resistor connected through jumper P2). All pins nicely labeled. Includes 8MHz and 32kHz cystals, power LED and 20 pin JTAG connector. Boot 0 and 1 pins brought out to 2.4mm pin header for boot mode selection. Serial connections have their own 4pin header with GND and 5V. Nothing else. A good point is V_BAT is brought out to pin header as well. Schematics can be found if you search by "lctech-stm32-devboard-scheme", but the only thing that needs explanation is jumper P2. The bad part: Soldering of SMD components is just passable We have come to expect better even from China. Soldering of through hole components is not very good. Pin headers are on crooked. Some people may prefer pin headers soldered at the other side. Banggood hear us: Please offer this product with pin headers left off! Overall, a good product which will benefit from better through hole soldering, or better, pin headers completely left off.

    Komentarze
    Pokaż oryginał
  • 25/11/2014

    I have seen it listed on other sites but not a this this price. I connected it to J-link JTAG,USB power , Open KEIL, compile test project and it worked. Just as I was expecting.

    Komentarze
    Pokaż oryginał
  • 19/05/2015

    Great board for the best price. The Cortex-M3 CPU is great, very powerful and the chip has tons of periphery. I like the fact the board has the RTC xtal mounted. Great open source support - libopencm3 + GNU ARM toolchain + Eclipse. + OpenOCD.

    Komentarze (3)
    Pokaż oryginał
  • LMPVIP4
    PT
    14/01/2020

    Dobra

    Komentarze
    Pokaż oryginał
  • 12/06/2016

    Zum Download über TX RX die Bootjumper *- BOOT0 -* BOOT1 so stecken. Nutze dafür den CH340 in NANO (Achtung Widerstände anpassen sonst langen die Pegel nicht und RESET jumpern) Es gibt nun auch noch eine schmälere Version.

    Komentarze
    Pokaż oryginał
  • 17/04/2014

    Perfect small board to start with STM32 development, well constructed and has everything required...

    Komentarze
    Pokaż oryginał
  • 03/01/2016

    Tested with some small project with GNU ARM compiler and Open CMSIS library. Very good results. Thanks for good product.

    Komentarze
    Pokaż oryginał
  • 11/12/2020

    Produkt pasuje do opisu.

    Komentarze
    Pokaż oryginał
  • 25/09/2020

    Jeszcze nie testowany, otrzymany 7 dni po złożeniu zamówienia

    Komentarze
    Pokaż oryginał
  • 01/09/2019

    Impeccable ! Article d'une Qualité irréprochable et Conforme à sa description...

    Komentarze
    Pokaż oryginał
Show:

    Całkowity 0 stron

    Idź do strony

    recommendation for you
    • US$10.99
    • US$4.99
    • US$5.99
    • US$6.99
    • US$5.99
    • US$5.74
    • US$24.49
    • US$11.49
    • US$16.09
    • US$36.95
    • US$33.62
    • US$63.19
    • US$9.99
    • US$8.99
    • US$39.99
    • US$32.99
    • US$18.99
    • US$47.29