Recenzje 5szt. Czujnik Prędkości Pomiarowej Przełącznik Licznika Testowy Entliczek PENTliczek Moduł Geekcreit do Arduino - produkty, które działają z oficjalnymi płytami Arduino

5szt. Czujnik Prędkości Pomiarowej Przełącznik Licznika Testowy Entliczek PENTliczek Moduł Geekcreit do Arduino - produkty, które działają z oficjalnymi płytami Arduino

US$6.99
~~US$13.85~~
Kup Teraz

Opinie klientów

5 z5

Zobacz wszystkie recenzje w38

5 gwiazda
38 (100.0%)
4 gwiazda
0 (0%)
3 gwiazda
0 (0%)
2 gwiazda
0 (0%)
1 gwiazda
0 (0%)

Napisać recenzję Uzyskaj podwójne oceny, jeśli jesteś jedną z pierwszych 3 opublikowanych recenzji!

Wszystkie recenzje(38)
Obrazy
Wideo(0)
Wszystkie gwiazdy
- Wszystkie gwiazdy(38)
- 5 Gwiazda(38)
- 4 Gwiazda(0)
- 3 Gwiazda(0)
- 2 Gwiazda(0)
- 1 Gwiazda(0)

Sortuj według:

Do podglądu

Do podglądu
Najbardziej pomocny
Najnowszy

Recenzje tylko z Twojego kraju (Poland)

Pokaż oryginał

Część recenzji została przetłumaczona automatycznie.

PlonsVIP3
12/11/2015

The output of this board can oscillate when the slot in the wheel is half open - half closed. The designer added a 100nF capacitor across the photo transistor but that makes the situation worse. To fix this problem, the capacitor closest to the edge of the board should be removed and a 33k resistor must be added between output (pin7) and the non-inverting input (pin5). I will post the schematic in a second. Note: if you poll the output in your software, you can omit the modification. But if you use an interrupt or clock-input, this mod is necessary.

The output of this board can oscillate when the slot in the wheel is half open - half closed. The designer added a 100nF capacitor across the photo transistor but that makes the situation worse. To fix this problem, the capacitor closest to the edge of the board should be removed and a 33k resistor must be added between output (pin7) and the non-inverting input (pin5). I will post the schematic in a second. Note: if you poll the output in your software, you can omit the modification. But if you use an interrupt or clock-input, this mod is necessary.

The output of this board can oscillate when the slot in the wheel is half open - half closed. The designer added a 100nF capacitor across the photo transistor but that makes the situation worse. To fix this problem, the capacitor closest to the edge of the board should be removed and a 33k resistor must be added between output (pin7) and the non-inverting input (pin5). I will post the schematic in a second. Note: if you poll the output in your software, you can omit the modification. But if you use an interrupt or clock-input, this mod is necessary.
7

Komentarze (2)

Pokaż oryginał
SEBASTIEN NOIRVIP1
FR
08/10/2017

The Product works as it is said in the description: It does not give you speed (speed calculations have to be done by the micro-controller) so the name "Speed Measuring Sensor" is a bit off. these modules could also be used as optical endstops for 3D printers

The Product works as it is said in the description: It does not give you speed (speed calculations have to be done by the micro-controller) so the name "Speed Measuring Sensor" is a bit off. these modules could also be used as optical endstops for 3D printers

The Product works as it is said in the description: It does not give you speed (speed calculations have to be done by the micro-controller) so the name "Speed Measuring Sensor" is a bit off. these modules could also be used as optical endstops for 3D printers
1

Komentarze

Pokaż oryginał