Product (as always with Banggood) arrived well within the stated delivery times and was well wrapped and protected which was lucky as the packet had obviously been dropped in the post as one of the corners was dented, but minimal damage (a couple of bent pins that were easily sorted) occurred. The stepper drivers were all well soldered and the heatsinks applied well without causing shorts across the pins (I've seen some poor quality ones on ebay that do!). Mine came adjusted almost perfectly but maybe that was just lucky, although I obviously had to adjust one of the them for the z-axis which uses two motors on my build. The only slight gripe I had with the steppers is that the plastic around the pins had not been cut away cleanly so I had to cut these down a little in order to be able to fit them end on end into the ramps board. The ramps board itself is great. All the soldering is well done, all the jumpers set correctly (do make sure you check yours though!) and the quality of the components looks good, especially considering the very reasonable cost of the board. Like all ramps boards however it uses screw down connectors that are not rated highly enough for the potential 16amp draw. I've not had a problem with this but have seen a few melted ones so if you are running a high draw setup it might be worth soldering the connections direct to the board instead of using the connectors/ Overall a great board, with good steppers, at a fantastic price.

Product (as always with Banggood) arrived well within the stated delivery times and was well wrapped and protected which was lucky as the packet had obviously been dropped in the post as one of the corners was dented, but minimal damage (a couple of bent pins that were easily sorted) occurred. The stepper drivers were all well soldered and the heatsinks applied well without causing shorts across the pins (I've seen some poor quality ones on ebay that do!). Mine came adjusted almost perfectly but maybe that was just lucky, although I obviously had to adjust one of the them for the z-axis which uses two motors on my build. The only slight gripe I had with the steppers is that the plastic around the pins had not been cut away cleanly so I had to cut these down a little in order to be able to fit them end on end into the ramps board. The ramps board itself is great. All the soldering is well done, all the jumpers set correctly (do make sure you check yours though!) and the quality of the components looks good, especially considering the very reasonable cost of the board. Like all ramps boards however it uses screw down connectors that are not rated highly enough for the potential 16amp draw. I've not had a problem with this but have seen a few melted ones so if you are running a high draw setup it might be worth soldering the connections direct to the board instead of using the connectors/ Overall a great board, with good steppers, at a fantastic price.

Product (as always with Banggood) arrived well within the stated delivery times and was well wrapped and protected which was lucky as the packet had obviously been dropped in the post as one of the corners was dented, but minimal damage (a couple of bent pins that were easily sorted) occurred. The stepper drivers were all well soldered and the heatsinks applied well without causing shorts across the pins (I've seen some poor quality ones on ebay that do!). Mine came adjusted almost perfectly but maybe that was just lucky, although I obviously had to adjust one of the them for the z-axis which uses two motors on my build. The only slight gripe I had with the steppers is that the plastic around the pins had not been cut away cleanly so I had to cut these down a little in order to be able to fit them end on end into the ramps board. The ramps board itself is great. All the soldering is well done, all the jumpers set correctly (do make sure you check yours though!) and the quality of the components looks good, especially considering the very reasonable cost of the board. Like all ramps boards however it uses screw down connectors that are not rated highly enough for the potential 16amp draw. I've not had a problem with this but have seen a few melted ones so if you are running a high draw setup it might be worth soldering the connections direct to the board instead of using the connectors/ Overall a great board, with good steppers, at a fantastic price.

Hi I bought 2 sets of these and they came in due time. The problem is that the heatsinks are missing the special heat transfer adhesive and I can't use them. Why did this happen? Also one set was completely different that the other, especial the drivers. Is it possible for banggood to send me the heat transfer adhesive ASAP ?

Hi I bought 2 sets of these and they came in due time. The problem is that the heatsinks are missing the special heat transfer adhesive and I can't use them. Why did this happen? Also one set was completely different that the other, especial the drivers. Is it possible for banggood to send me the heat transfer adhesive ASAP ?

Hi I bought 2 sets of these and they came in due time. The problem is that the heatsinks are missing the special heat transfer adhesive and I can't use them. Why did this happen? Also one set was completely different that the other, especial the drivers. Is it possible for banggood to send me the heat transfer adhesive ASAP ?

The ramps board was well packaged and works fine, but double check the Pololu drivers. All the heat sinks were touching the pins at one side and I have to remove them and and fixed them with a drop of superglue. The origin used therminal adhesive is not that strong and to remove the heat sinks was not a big deal.

The ramps board was well packaged and works fine, but double check the Pololu drivers. All the heat sinks were touching the pins at one side and I have to remove them and and fixed them with a drop of superglue. The origin used therminal adhesive is not that strong and to remove the heat sinks was not a big deal.

The ramps board was well packaged and works fine, but double check the Pololu drivers. All the heat sinks were touching the pins at one side and I have to remove them and and fixed them with a drop of superglue. The origin used therminal adhesive is not that strong and to remove the heat sinks was not a big deal.

Assemble the ok. havent test them yet

Assemble the ok. havent test them yet

Assemble the ok. havent test them yet

Elettronica perfetta

Elettronica perfetta

Elettronica perfetta

Usefull to make a 2nd Reprap

Usefull to make a 2nd Reprap

Usefull to make a 2nd Reprap

Based on a Prusa I3, with some small modifications in pins.h and marlin.cpp Heatbeat mosfet is driving the laser now. Swapped D8 en D9 in the Marlin firmware. Heatbed mosfet is fan mosfet now. Modifing M106 and M107 to be M03 and M05. M03 PWM.

Based on a Prusa I3, with some small modifications in pins.h and marlin.cpp Heatbeat mosfet is driving the laser now. Swapped D8 en D9 in the Marlin firmware. Heatbed mosfet is fan mosfet now. Modifing M106 and M107 to be M03 and M05. M03 PWM.

Based on a Prusa I3, with some small modifications in pins.h and marlin.cpp Heatbeat mosfet is driving the laser now. Swapped D8 en D9 in the Marlin firmware. Heatbed mosfet is fan mosfet now. Modifing M106 and M107 to be M03 and M05. M03 PWM.

toujours parfait une rapidité au top et sans problème avec toujours des solution

toujours parfait une rapidité au top et sans problème avec toujours des solution

toujours parfait une rapidité au top et sans problème avec toujours des solution

It is as decribed, but sadly there was a fatal solder problem, but it was easily correctable.

It is as decribed, but sadly there was a fatal solder problem, but it was easily correctable.

It is as decribed, but sadly there was a fatal solder problem, but it was easily correctable.

Ho acquistato la RAMPS e i driver per una seconda stampante 3D ma rispetto ad un precedente acquisto la ramps ha l pin disallineati per cui è difficile l'inserimento nella scheda Arduino. Due driver non funzionano e i dissipatori a corredo non hanno l'adesivo per attaccarli al 4988 dei driver.

Ho acquistato la RAMPS e i driver per una seconda stampante 3D ma rispetto ad un precedente acquisto la ramps ha l pin disallineati per cui è difficile l'inserimento nella scheda Arduino. Due driver non funzionano e i dissipatori a corredo non hanno l'adesivo per attaccarli al 4988 dei driver.

Ho acquistato la RAMPS e i driver per una seconda stampante 3D ma rispetto ad un precedente acquisto la ramps ha l pin disallineati per cui è difficile l'inserimento nella scheda Arduino. Due driver non funzionano e i dissipatori a corredo non hanno l'adesivo per attaccarli al 4988 dei driver.