Opinie klientów

4.82 z5
Napisać recenzję
  • Wszystkie recenzje(22)
  • Obrazy
  • Wideo(0)
  • All Star
    • All Star(22)
    • 5 Star(18)
    • 4 Star(4)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sortuj według:
Do podglądu
  • Do podglądu
  • Najbardziej pomocny
  • Najnowszy
Recenzje tylko z Twojego kraju (Hungary)
  • June-24 2020 17:10:40

    Was great for few test welds and then began to sparks fly from PCB, one small transistor melted and few mosfets went hot and bit smoke. I read one review where was similar case like i have, not sure did we just get bad monday items or what. Small minus, does not contain any instructions, for example what led colors means would be great.

    Komentarze (1)
  • October-06 2020 16:46:06

    it works well, using 4S lipo battery. when using first and second level of power, device and battery do not get too much hot, so you could make many spot weldings.

  • December-01 2020 09:41:12

    The spot welder works like a charm. Before using, make sure to solder the capacitor to the input of the device. I spot welded a 1.5 mm thick nickel strip with the LVL 3 power (Blue colour). For the best result use a big 4s lipo Battery. I used a 5000 mAh 60C lipo. You need at lease 150A discharge current for the device to work properly (You can calculate the max discharge current by multiplying the capacity with the C rating. For example, if the Lipo has 2000mAh and 100C the calculation should look

  • August-06 2020 20:40:38

    This board is very nice, and works quite well. So far very happy with this board. The mounting holes are very small. The positive is a 2mm hole, and the negative is 3mm. I made a brass extender for the positive on my Mini Lathe. Used a 3mm brass riser and turned down the 3mm screw end to 2mm to fit the hole on the board. I then soldered this to the board, so I had a 3mm location to mount the positive connection. I had some welding tips from another board that failed, So I used those. Had to use

  • January-16 2021 04:16:24

    Sehr gute und günstige Lösung, durch die Möglichkeit die Schweißzeit einzustellen lässt sich die Leistung gut regulieren. Der strom lässt sich über den Ladezustand der Akkus und der Kapazität/c raten beeinflussen. Was am Anfang etwas probieren erfordert. Am besten erstmal nur die Nikelstreifen verschweißen da bei zu höhen Einstellungen die zu verscheschweißende Zelle beschädigt werden kann.

  • August-01 2020 21:20:12

    Seems to do what I need done using the Red and Green settings. Purple BLOWS holes in 18650 cells. LOL Bet folks would be willing to pay a extra dollar for documented instructions ? I located the Cap on the underside.

  • June-12 2020 15:01:57

    not to happy with item no one knows where to solder capacitor! finaley figured it out , worked great firs time then burned out 2 x fets on second try!

  • September-18 2020 07:54:45

    thank you

  • June-20 2020 09:27:52

    Works good. Included Instructions would be great.

  • January-20 2021 06:29:01

    gute Sxchweißnadeln


    Total 0 pages

    Go to page


    Możesz być zainteresowany

    recommendation for you
    • Ft5,091
    • Ft5,691
    • Ft2,095
    • Ft1,795
    • Ft596
    • Ft6,590
    • Ft2,394
    • Ft4,777
    • Ft596
    • Ft2,943
    • Ft2,304
    • Ft7,489
    • Ft7,788
    • Ft2,095
    • Ft1,196
    • Ft5,091
    • Ft2,817
    • Ft3,419